Return to the home page...

Go Back   Moyer Marine Atomic 4 Community - Home of the Afourians > Discussion Topics > Safety

Reply
 
Thread Tools Display Modes
  #1   IP: 66.87.116.124
Old 07-29-2016, 01:54 PM
azazzera azazzera is offline
Senior Member
 
Join Date: Aug 2014
Posts: 171
Thanks: 0
Thanked 8 Times in 6 Posts
If you think it can't happen.

Not that any one would realy dismiss the possibility of a non ingnition protected devise could ignite gas vapors that's exactly what happened on the east end of Long Island today. Clearing the residual water out of bildge and there obviously was enough gasoline vapors present to ignite and cause an explosion. Luckily hatches were open. Nothing life threatening. Three victims. I emediatly thought of what many have warned about on this sight. It's just timely for me having just gotten my boat in yesterday. I will be getting that blower installed first thing. Very thankful for all the excellent advice I get here.
Reply With Quote
The Following 3 Users Say Thank You to azazzera For This Useful Post:
Dave Neptune (07-29-2016), sastanley (07-29-2016), toddster (07-29-2016)
  #2   IP: 67.237.237.64
Old 07-29-2016, 04:06 PM
toddster toddster is online now
Senior Member
 
Join Date: Aug 2011
Posts: 388
Thanks: 5
Thanked 14 Times in 13 Posts
Hmm... I had assumed that all bilge pumps would be ignition protected. And float switches? Of course none of us would attempt to discharge fuel anyway...

Believe me, after I discovered a fuel leak last week, I cut all power to the boat and Very Carefully cleaned the bilge. And hosed out that inaccessible sump under the motor. And left the hatches and bilge hatches open for a couple of days. Fortunately, one of my suppliers uses those synthetic fuel-absorbent pads as packing material, so I have stacks of them around.
Reply With Quote
  #3   IP: 76.179.157.47
Old 07-29-2016, 05:03 PM
BunnyPlanet169's Avatar
BunnyPlanet169 BunnyPlanet169 is offline
Afourian MVP
 
Join Date: May 2010
Location: York, ME
Posts: 949
Thanks: 25
Thanked 70 Times in 56 Posts
UL listed bilge pump yes, large shop vac or electric drill not so much....
__________________
Jeff


S/V Bunny Planet
1971 Bristol 29 #169
Reply With Quote
  #4   IP: 66.87.117.92
Old 07-29-2016, 06:20 PM
azazzera azazzera is offline
Senior Member
 
Join Date: Aug 2014
Posts: 171
Thanks: 0
Thanked 8 Times in 6 Posts
Just for background, this happened at a yard. They were useing a external sump type pump to pump out residual water after pulling a plug. Must have had fuel leak. Burn victim had 21 years at the yard. As my sister says, safety's no accident!!!! Never bad ide to take that extra few steps to make sure it's safe.
Reply With Quote
  #5   IP: 24.152.132.65
Old 07-29-2016, 06:30 PM
ndutton's Avatar
ndutton ndutton is online now
Afourian MVP
 
Join Date: May 2009
Location: Torrance, CA
Posts: 7,179
Thanks: 75
Thanked 530 Times in 366 Posts
I could tell ya some stories from the boat plants with acetone rather than gasoline. Three come immediately to mind.

The first place I worked issued pneumatic tools to us: drills, screw guns, sawzalls, jigsaws, sanders & grinders, all pneumatic. Electric tools were not allowed, period. It was odd that as we worked the tools hard they got ice cold, even painful to hold, exactly the opposite of electric tools.
Reply With Quote
  #6   IP: 71.178.85.239
Old 07-29-2016, 09:30 PM
sastanley's Avatar
sastanley sastanley is offline
Afourian MVP
 
Join Date: Sep 2008
Location: Solomons, MD
Posts: 6,046
Thanks: 269
Thanked 169 Times in 131 Posts
When my boat sprung a leak in the fuel tank, and several gallons went in the bilge, all battery connections were disconnected with the batt switch at "OFF", and all fluid, including the copious amounts of water added to dilute the fuel as advised by an airplane mech Navy Chief, was bailed by hand in 5 gallon buckets from the bilge to the disposal area using cups & sponges.
__________________
-Shawn
"Twice Around" - '77 Catalina 30, #511 with original A-4 & MMI manifold.
Spring is here!!

http://www.moyermarine.com/forums/signaturepics/sigpic3231_6.gif
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Don't let this happen to you rpowers General Maintenance 6 04-07-2010 09:23 PM
Turning off Sea Cock Valve Phil_E General Maintenance 8 03-14-2009 12:53 AM


All times are GMT -5. The time now is 08:19 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2017, vBulletin Solutions, Inc.


Universal® is a registered trademark of Westerbeke Corporation

Copyright © 2004-2017 Moyer Marine Inc.

All Rights Reserved